#CETUS3D FIRMWARE INSTALL#
#CETUS3D FIRMWARE UPDATE#
#CETUS3D FIRMWARE UPGRADE#
#CETUS3D FIRMWARE SOFTWARE#

When I wantetd to print the first time (alfter leveling of course) the Nozzle first cleans (one straight line) which was ok.

#CETUS3D FIRMWARE SOFTWARE#

Init via software is working and the endstops are working too. the hardware Init switch did not work anymore !!!!!! Therefore I hab to drill 4 more holes in the Baseplate to shift the Mainboard about 5mm to the middle.ДЄfter installing all the hardware I flashed the CPU with

When the Mainboard was installed it was too close to the baseplate edge so that I could not put the Cover back on again. MK3 Standard Version ROM:ДЇor the z axis I had to use the original cap to make a hole for the endstop because the linear rail from my printer seems to be shorter (the black part is the new one from the link above (didn't fit).

#CETUS3D FIRMWARE UPDATE#

Lock the extruder cable along the Z-axisД¬PU rom must be updated before the machine is usable, please refer to following info to update your rom.

#CETUS3D FIRMWARE UPGRADE#

This ribbon cable is important for temprature control of heated bed upgrade and autoleveling.ДЎ0.1 Insert the antenna holder into the slot of the back of machine, turn it 90 degrees to lock it in position.ДЎ0.2 Insert the antenna into the holder and connect the other end to CPU.ДЎ0.3 Make sure the cables are well sorted, no tangling. Insert the cable into the connector, metal pins facing to mainboard.Д©.5 Fold the cable into shape like the red line indicated below.Д©.6 Insert the ribbon cable through the space between motor and Z-axis bracket.Д©.7 Fold the cable upward and insert into the connector, metal pins facing toward extension board. Follow the color.Д©.2 Connect the limit switches from extension PCB to mainboard, using the included relay cable.Д©.3 Connect the power cable from extension PCB to mainboardД©.4 Loosen the connector (labelled as ' Platform Heater) for ribbon cable.

#CETUS3D FIRMWARE INSTALL#

Install MK3 Z-axis Cap and Limit Switch.Д©.1 Connec Z-limit switch and Y-limit switch to the extension board. Installation Guide of Extension PCB for Cetus MK3Дetailed Guidance on Extension Board Installation and Limited Switch IssuesД§.2 Slide the extension board into extrusion slot. Install limit switch holder onto the Y-axis motor.Д¦.1 Open the slot cover on the back of the printer.Д¦.2 Press the holder into the slot, install the limit switch.Д¦.3 Position the motor cable and limit switch cable into the slot and press fit the slot cover.Д¬hapter 4. Remove the original printed part and the screw on the motor.ДҐ.3. Install the limit switch on the holder.ДҐ.2. Install the New Y Limit Switch TriggerДҐ.1. Do not remove the screw from the belt, keep it on the belt!Д¤.3. Lossen the screw on the back of the belt, remove the printed part. Install Y-axis Limit Switch and Trigger.Д¤.2. Connect Ground Cable (reduce risk of static charge damage to electronics) Install MK3 Mainboard, CPU and SD card.ДЈ.4. Fabbaloo: The Cetus 3D Printer is priced at an amazingly low USD199 for the super early bird Kickstarter pricing. We spoke with TiertimeвЂ™s Jason Wu, product manager of the new Cetus desktop 3D printer to find out more about this inexpensive device. Remove the 4 screws on mainboard, unplug the extruder cable, motor cables and remove the mainboard.ДЈ.2 Install the Mainboard Adaptor and MK3 Mainboard.ДЈ.3. The Cetus desktop 3D printer comes in two sizes. Before remove the CPU, discharging yourself is recommended, also be careful not to bend the pin of the CPU board.Дў.6. Remove the power cable and the initialization button cable.Дў.4. Remove the platform by removing the 3 scerws.Дў.2 Remove the 4 screws to the bottom of machine.Дў.3. Print Plastic Parts Required for UpgradeД«efore dissasembling everything, printer out the parts required.Дownload the following file for the printable parts:Дў.1. User have to use the 220W Power Supply (sku:XS028). The following images display the correct Z+ endstop pin location for the installation for the Filament Runout Sensor.After upgrade, if user install the heated build platform, original power supply cannot be used to supply power to the machine. Once the firmware is configured and uploaded to your printer, Marlin will send M600 gcode to change the filament spool once the sensor is triggered. More information about the firmware configuration is available at the official Marlin Documentation found here. Once done, flash the modified firmware to your printer. Modify Configuration_adv.h in the section Advanced Pause and uncomment the following line: #define ADVANCED_PAUSE_FEATURE Step 6 If you need to invert the logic of the sensor set to true the following line: #define FIL_RUNOUT_INVERTING false Step 5 Since the sensor has its own pull-up resisters comment the following line: //#define FIL_RUNOUT_PULLUP Step 4 In this case, I used the Z+ Port, therefore you need to set FIL_RUNOUT_PIN in pins_RAMPS.h to 19, add the following line to the block of code: #define FIL_RUNOUT_PIN 19 Step 3 Modify Configuration.h on Filament Runout Sensors section uncomment the following line: #define FILAMENT_RUNOUT_SENSOR Step 2

Cetus3d firmware